Updates

content/SUMMARY.md

@@ -37,6 +37,7 @@
         - [🗈 Mini Drak build condensed instructions](model-build-notes/mini-drak-build-condensed-instructions.md)
 - [📁 Maker things](maker-things/index.md)
     - [🗈 Battery discharge curves](maker-things/battery-discharge-curves.md)
+    - [🗈 Details about my Sapphire Pro](maker-things/details-about-my-sapphire-pro.md)
     - [🗈 Electronics tips](maker-things/electronics-tips.md)
     - [🗈 GRBL_ESP32 tips](maker-things/grbl-esp32-tips.md)
     - [🗈 How to properly level your 3D printer](maker-things/how-to-properly-level-your-3d-printer.md)

content/maker-things/details-about-my-sapphire-pro.md

@@ -0,0 +1,16 @@
+# Details about my Sapphire Pro
+
+My Sapphire Pro runs the MKS Robin Nano 1.2 board. Details on that board (pinouts, diagrams, etc) are here:
+
+https://github.com/makerbase-mks/MKS-Robin-Nano-V1.X/wiki/Wiring_Pinout_and_Size
+
+I've installed TMC2209 drivers and wired all their UARTs up to the same pin, PA13. Their addresses for X, Y, Z, and E are 0, 1, 2, and 3, respectively. It doesn't work with Klipper, I'm only getting the error message `TMC stepper_x failed to init: Unable to read tmc uart 'stepper_x' register IFCNT`. Nothing I've tried has worked. If you managed to make this work, please email me.
+
+I've installed the SFS 2.0 motion runout sensor on MT_DET1 and MT_DET2. This means that the motion sensor pin is PE6, and the switch sensor is PA4. That doesn't work either, Marlin keeps thinking the printer has run out of filament.
+
+* * *
+
+<p style="font-size:80%; font-style: italic">
+Last updated on April 05, 2024. For any questions/feedback,
+email me at <a href="mailto:hi@stavros.io">hi@stavros.io</a>.
+</p>

content/maker-things/index.md

@@ -3,6 +3,7 @@
 Click on a link in the list below to go to that page:
 
 1. [Battery discharge curves](../../maker-things/battery-discharge-curves.html)
+1. [Details about my Sapphire Pro](../../maker-things/details-about-my-sapphire-pro.html)
 1. [Electronics tips](../../maker-things/electronics-tips.html)
 1. [GRBL_ESP32 tips](../../maker-things/grbl-esp32-tips.html)
 1. [How to properly level your 3D printer](../../maker-things/how-to-properly-level-your-3d-printer.html)

content/software/cloning-cards-fobs-with-a-proxmark3.md

@@ -28,28 +28,47 @@ lf em 410x reader
 
 You should be done, but I haven't tested it as I don't have a Paxton reader handy.
 
-### Related reading
-
-* [Iceman's Proxmark3 firmware (use this one)](https://github.com/RfidResearchGroup/proxmark3)
-* [How to copy Paxton fobs using an RFIDler](https://gist.github.com/natmchugh/18e82761dbce52fa284c87c190dc926f#getting-hold-of-hitag2-tags)
-* [ How to copy, read and write Paxton fobs and cards with a Proxmark ](https://badcfe.org/how-to-paxton-with-proxmark/)
 
 ## Cloning MiFare cards
 
 See [Cloning a Mifare Classic 1K](https://www.gavinjl.me/proxmark-3-cloning-a-mifare-classic-1k/).
 
-## Card cloner
 
-I have an AliExpress cloner which clones LF cards. Unfortunately, whenever it clones a card, it sets the password bit on it. To remove it with the Proxmark3, run:
+## Card cloner password
+
+I have an AliExpress cloner which clones LF cards. Unfortunately, whenever it clones a card, it sets the password bit on it. This makes the card not respond to writes/wipes without the password (it just keeps having the same data, no matter what you write).
+
+To remove it with the Proxmark3, run:
 
 ```
-lf t55 wipe --p 51243648
+lf t55 wipe -p 51243648
 ```
 
 
+## Cloning T5577 cards
+
+Read the card with:
+
+```
+lf em 410x reader
+```
+
+Write with:
+
+```
+lf EM 410x clone --id <the ID from before>
+```
+
+
+## Related reading
+
+* [Iceman's Proxmark3 firmware (use this one)](https://github.com/RfidResearchGroup/proxmark3)
+* [How to copy Paxton fobs using an RFIDler](https://gist.github.com/natmchugh/18e82761dbce52fa284c87c190dc926f#getting-hold-of-hitag2-tags)
+* [ How to copy, read and write Paxton fobs and cards with a Proxmark ](https://badcfe.org/how-to-paxton-with-proxmark/)
+
 * * *
 
 <p style="font-size:80%; font-style: italic">
-Last updated on February 24, 2024. For any questions/feedback,
+Last updated on March 04, 2024. For any questions/feedback,
 email me at <a href="mailto:hi@stavros.io">hi@stavros.io</a>.
 </p>