Update

content/drone-stuff/_index.md

@@ -10,7 +10,6 @@ Click on a link in the list below to go to that page:
 
 1. [Getting uninverted SBUS on a no-name FrSky-compatible receiver](../../drone-stuff/getting-uninverted-sbus-on-a-no-name-frsky-compatible-receiver)
 1. [Getting uninverted SBUS/SmartPort on the FrSky XSR receiver](../../drone-stuff/getting-uninverted-sbus-smartport-on-the-frsky-xsr-receiver)
-1. [Mini Drak build condensed instructions](../../drone-stuff/mini-drak-build-condensed-instructions)
 1. [Omnibus F4 V3 pinout](../../drone-stuff/omnibus-f4-v3-pinout)
 1. [Omnibus F4 pro servo diode](../../drone-stuff/omnibus-f4-pro-servo-diode)
 1. [Transmitter external module pinout](../../drone-stuff/transmitter-external-module-pinout)

content/drone-stuff/omnibus-f4-pro-servo-diode.md

@@ -1,6 +1,6 @@
 +++
 title = "Omnibus F4 pro servo diode"
-weight = 4
+weight = 3
 sort_by = "weight"
 insert_anchor_links = "right"
 +++

content/drone-stuff/omnibus-f4-v3-pinout.md

@@ -1,6 +1,6 @@
 +++
 title = "Omnibus F4 V3 pinout"
-weight = 3
+weight = 2
 sort_by = "weight"
 insert_anchor_links = "right"
 +++

content/drone-stuff/transmitter-external-module-pinout.md

@@ -1,6 +1,6 @@
 +++
 title = "Transmitter external module pinout"
-weight = 5
+weight = 4
 sort_by = "weight"
 insert_anchor_links = "right"
 +++

content/model-build-notes/_index.md

@@ -0,0 +1,12 @@
++++
+title = "Model build notes"
+weight = 4
+sort_by = "weight"
+insert_anchor_links = "right"
++++
+## Contents
+
+Click on a link in the list below to go to that page:
+
+1. [Building notes for the FT Mighty Mini Arrow](../../model-build-notes/building-notes-for-the-ft-mighty-mini-arrow)
+1. [Mini Drak build condensed instructions](../../model-build-notes/mini-drak-build-condensed-instructions)

content/model-build-notes/building-notes-for-the-ft-mighty-mini-arrow.md

@@ -0,0 +1,67 @@
++++
+title = "Building notes for the FT Mighty Mini Arrow"
+weight = 0
+sort_by = "weight"
+insert_anchor_links = "right"
++++
+These notes are a condensed version of the [FT Arrow build video](https://www.youtube.com/watch?v=cD2Ca2oskVs).
+
+![maxresdefault.jpeg](../../resources/d4819ca1c3d0490daaa12f62af09aa00.jpeg)
+
+
+## Wings
+
+* Do an "A" fold on the spars and glue, stop 15mm from each edge. Use a triangle to make sure the spar folds are perpendicular.
+* Open the servo hole.
+* Cut the bevels, double on wing and single on elevon (on the elevon side).
+* Add a thin ribbon on glue on the bottom of the hinge for strength, and scrape almost all of it off.
+* Remove servo pocket from the wing.
+* Fold the wing with the bottom on top, to curve the leading edge without crinkling the airfoil score cuts.
+* Cut the side pods if you aren't going to use a center pod.
+* Glue the side pod hinges.
+* Cut the main pod space on the top of the wing.
+* Skewer the wing score cuts.
+* Line up the spar's servo hole onto the wing and glue.
+* Glue the airfoil's score cuts and fold the wing so the score cuts are glued up.
+* Cut the excess spar.
+* Probably put the servos in now, to avoid having to make a hook later.
+* Glue the leading edge, bottoms of the spar, and the end of the trailing edge, and press closed.
+
+
+### Joining the wings
+
+* Tape the wings together at the bottom, glue them together in the middle, lay them down and wipe the excess glue.
+* Cut the excess edge of the nose.
+
+
+## Center pod
+
+* Pop out the foam tabs on the wings, where the center pod will go.
+* Pop out the tabs on the center pod.
+* Do an "A" fold on the bottom plate.
+* Fold the little edge of the top of the center pod over (and/or add tape).
+* Glue the center pod on.
+* Install the control horns and servos (I use epoxy for the control horns as they tend to get ripped out with just hot glue).
+* Use the reflex checker foam to calibrate the wing's reflex.
+* Add a ziptie to the control rod so it doesn't bend.
+
+
+## Power pod
+
+* Install the motor onto the power pod and install the power pod. You probably don't need to glue this, just make sure it's tight.
+* Remove the foam from the sides of the nose.
+* Do a "C" fold on the back bit (and probably add some tape).
+* Carefully bend the nose.
+* Test fit it and glue the front part.
+* Use more tape to secure the front and sides.
+* Add some tape so you can pull the top open.
+* Add some glue to the bottom of the top hatch so it catches and secures on close.
+
+## Winglets
+
+* Only cut the top part of the wing, parallel to the bottom.
+* Line up the reference line on the winglets and glue (the front tip of the winglet should be flush with the leading edge).
+
+## Electronics
+
+* The rest is left as an exercise to the reader.

content/model-build-notes/mini-drak-build-condensed-instructions.md

@@ -1,6 +1,6 @@
 +++
 title = "Mini Drak build condensed instructions"
-weight = 2
+weight = 1
 sort_by = "weight"
 insert_anchor_links = "right"
 +++