101 lines
4.1 KiB
Markdown
101 lines
4.1 KiB
Markdown
+++
|
|
title = "Tuning the TECS"
|
|
weight = 6
|
|
sort_by = "weight"
|
|
insert_anchor_links = "right"
|
|
+++
|
|
|
|
To tune the TECS, a helpful resource is the official [TECS tuning guide](https://ardupilot.org/plane/docs/tecs-total-energy-control-system-for-speed-height-tuning-guide.html).
|
|
Make sure you have run an autotune beforehand, and continue with the tuning below.
|
|
|
|
In tuning, there are three stages:
|
|
|
|
- Prepare to measure
|
|
- Take measurements in the field.
|
|
- Set parameters on the bench, based on your measurements.
|
|
|
|
### Preparation
|
|
- [ ] Set `LIM_PITCH_MAX=4500` (centidegrees), or something similarly high.
|
|
This is the maximum pitch you'll be achieving in FBWA, and you don't want to be limited by this while trying to tune.
|
|
- [ ] Set `LIM_PITCH_MIN=-4500` (centidegrees) or something similarly low.
|
|
This is the minimum pitch you'll be achieving in FBWA, and you don't want to be limited by this either.
|
|
|
|
|
|
### In the field
|
|
You should perform the measurements in four stages, all in the FBWA mode:
|
|
|
|
#### Fly straight
|
|
Fly straight and note down:
|
|
|
|
- [ ] The maximum speed you want to be flying at (in km/h).
|
|
- [ ] The throttle percentage at that maximum speed.
|
|
- [ ] Start a turn at the maximum bank angle (full roll deflection to one side) and note the slowest speed you can fly at without stalling.
|
|
- [ ] Fly straight at a speed 15% higher than the stall speed from the previous step, and note that speed. This is your trim speed.
|
|
- [ ] Note the throttle percentage at that speed.
|
|
- [ ] Turn throttle to 0 and pitch down a bit so you don't stall.
|
|
Note the minimum amount of down-pitch required to keep you from stalling (this should only be in the 1-3 degree ballpark).
|
|
|
|
#### Fly up
|
|
Set the throttle to the maximum throttle percentage from the previous step and start slowly pitching up until your airspeed equals your trim speed from the previous step.
|
|
If you're higher than that speed and need to climb more, change `LIM_PITCH_MAX` to something higher and try again.
|
|
Note down:
|
|
|
|
- [ ] The pitch angle (in degrees).
|
|
- [ ] The vertical speed from the variometer (in m/s).
|
|
|
|
#### Fly down
|
|
Set the throttle to 0 and start pitching down until your airspeed equals your trim speed from the previous step.
|
|
Note down:
|
|
|
|
- [ ] The vertical speed from the variometer (in m/s).
|
|
|
|
#### Fly down more
|
|
Keep the throttle at 0 and pitch down until you reach your desired maximum speed from step 1.
|
|
If you're lower than that speed and need to pitch down more, change `LIM_PITCH_MIN` to something lower and try again.
|
|
Note down:
|
|
|
|
- [ ] The pitch angle (in degrees).
|
|
- [ ] The vertical speed from the variometer (in m/s).
|
|
|
|
You're done with this step.
|
|
|
|
|
|
### On the bench
|
|
After you have the above measurements, you're ready to tune things. You can use the automatic calculator:
|
|
|
|
### [TECS tuning calculator](../../ardupilot/tecs-tuning-calculator)
|
|
|
|
Otherwise, you can do things manually, following the steps below, but you should really use the calculator instead.
|
|
|
|
For the level flight measurements:
|
|
|
|
- [ ] Set `ARSPD_FBW_MAX` (m/s) to something a bit less than the maximum airspeed you achieved in level flight.
|
|
- [ ] Set `THR_MAX` (percentage) to the throttle percentage at max speed.
|
|
- [ ] Set `ARSPD_FBW_MIN` (m/s) to the slowest speed you could turn at without stalling (maybe go a bit higher for some margin).
|
|
- [ ] Set `TRIM_ARSPD_CM` (cm/s) to your trim speed.
|
|
- [ ] Set `TRIM_THROTTLE` (percentage) to your trim throttle percentage.
|
|
- [ ] Set `STAB_PITCH_DOWN` (degrees) to the pitch angle that keeps you from stalling.
|
|
|
|
For the ascent measurements:
|
|
|
|
- [ ] Set `TECS_PITCH_MAX` (degrees) to the pitch angle you measured.
|
|
- [ ] Set `TECS_CLMB_MAX` and `FBWB_CLIMB_RATE` (both in m/s) to the climb rate you measured.
|
|
|
|
For the descent measurements:
|
|
|
|
- [ ] Set `TECS_SINK_MIN` (m/s) to the descent rate you measured.
|
|
|
|
For the max descent measurements:
|
|
|
|
- [ ] Set `TECS_PITCH_MIN` (degrees) to the pitch angle you measured.
|
|
- [ ] Set `TECS_SINK_MAX` (m/s) to the descent rate you measured.
|
|
|
|
That's it!
|
|
|
|
* * *
|
|
|
|
<p style="font-size:80%; font-style: italic">
|
|
Last updated on September 07, 2021. For any questions/feedback,
|
|
email me at <a href="mailto:hi@stavros.io">hi@stavros.io</a>.
|
|
</p>
|