67 lines
2.7 KiB
Markdown
67 lines
2.7 KiB
Markdown
+++
|
|
title = "Building notes for the FT Mighty Mini Arrow"
|
|
weight = 0
|
|
sort_by = "weight"
|
|
insert_anchor_links = "right"
|
|
+++
|
|
These notes are a condensed version of the [FT Arrow build video](https://www.youtube.com/watch?v=cD2Ca2oskVs).
|
|
|
|
|
|
|
|
|
|
## Wings
|
|
|
|
* Do an "A" fold on the spars and glue, stop 15mm from each edge. Use a triangle to make sure the spar folds are perpendicular.
|
|
* Open the servo hole.
|
|
* Cut the bevels, double on wing and single on elevon (on the elevon side).
|
|
* Add a thin ribbon on glue on the bottom of the hinge for strength, and scrape almost all of it off.
|
|
* Remove servo pocket from the wing.
|
|
* Fold the wing with the bottom on top, to curve the leading edge without crinkling the airfoil score cuts.
|
|
* Cut the side pods if you aren't going to use a center pod.
|
|
* Glue the side pod hinges.
|
|
* Cut the main pod space on the top of the wing.
|
|
* Skewer the wing score cuts.
|
|
* Line up the spar's servo hole onto the wing and glue.
|
|
* Glue the airfoil's score cuts and fold the wing so the score cuts are glued up.
|
|
* Cut the excess spar.
|
|
* Probably put the servos in now, to avoid having to make a hook later.
|
|
* Glue the leading edge, bottoms of the spar, and the end of the trailing edge, and press closed.
|
|
|
|
|
|
### Joining the wings
|
|
|
|
* Tape the wings together at the bottom, glue them together in the middle, lay them down and wipe the excess glue.
|
|
* Cut the excess edge of the nose.
|
|
|
|
|
|
## Center pod
|
|
|
|
* Pop out the foam tabs on the wings, where the center pod will go.
|
|
* Pop out the tabs on the center pod.
|
|
* Do an "A" fold on the bottom plate.
|
|
* Fold the little edge of the top of the center pod over (and/or add tape).
|
|
* Glue the center pod on.
|
|
* Install the control horns and servos (I use epoxy for the control horns as they tend to get ripped out with just hot glue).
|
|
* Use the reflex checker foam to calibrate the wing's reflex.
|
|
* Add a ziptie to the control rod so it doesn't bend.
|
|
|
|
|
|
## Power pod
|
|
|
|
* Install the motor onto the power pod and install the power pod. You probably don't need to glue this, just make sure it's tight.
|
|
* Remove the foam from the sides of the nose.
|
|
* Do a "C" fold on the back bit (and probably add some tape).
|
|
* Carefully bend the nose.
|
|
* Test fit it and glue the front part.
|
|
* Use more tape to secure the front and sides.
|
|
* Add some tape so you can pull the top open.
|
|
* Add some glue to the bottom of the top hatch so it catches and secures on close.
|
|
|
|
## Winglets
|
|
|
|
* Only cut the top part of the wing, parallel to the bottom.
|
|
* Line up the reference line on the winglets and glue (the front tip of the winglet should be flush with the leading edge).
|
|
|
|
## Electronics
|
|
|
|
* The rest is left as an exercise to the reader. |